Q. What should children know about electrical safety when they play outside?

A. Assume overhead lines are power lines and stay away from them. Do not climb trees,or fly kites near power lines, never attempt to remove something that may be caught on an overhead line. Never touch anyone who is in contact with a power line, call 911. Get inside at the first sign of lightning. Do not seek shelter under a tree. 

Q. How do we keep our pets safe from electrical hazards?

A. Make sure that your pet(s) do not use electrical devices or toys.The same frayed electrical  cord that delivers an electrical shock to an adult, have enough voltage to kill a dog or cat. Keep those electrical cords away from puppies and kittens.  If you have difficulty getting your pet to   stop chewing on the cord, you may want to wrap the cord in a   thick plastic sleeve. Keep Halogen lamps away from play areas for pets and children. Some Halogen bulbs can reach temperatures of 1,000 degrees. A fire can easily begin, if the lamp is knocked over   during play.
 

Q. My Smoke detector keeps beeping. What should I do?

A.   Detectors   start chirping when either of the following happens: 1. the   battery that is in the smoke detector is dying, or 2. The   smoke detector is dying. (This can happen in dusty   conditions more such as having your home painted etc.) Our   recommendations of the following is to have us replace your   smoke detectors throughout your home with Smoke / carbon   monoxide detectors with Lithium batteries installed. They   should last a good 5 years. The average life span of smoke   detectors is 5 years and it is recommended by manufacturers   to replace them every 5 years. The national fire protection   agency suggests every 10 years.

Q. Why do   my light bulbs burn out so fast?

A.   You may be exceeding the maximum lamp wattage of the fixture. (There   should be a label inside the fixture). Do not exceed 60   watts for most ceiling fixtures.  Another reason may be   vibration.  Vibration is the culprit in short bulb life.   There are vibration resistant bulbs for ceiling fans and   garage door opener and there are rough service bulbs for   portable lights. For lights such as recessed lights,   consider replacing the bulbs to bulbs that are rated 130VAC,   instead of the standard 120VAC bulbs you currently have. 

Q. Can I replace a standard wall switch with a dimmer?

A. A dimmer   easily replaces a standard wall switch and uses the exact   same wiring. Some light bulbs may not be suitable for   dimming. 

Q. Can a dimmer control a ceiling fan?

A. A dimmer   cannot control a ceiling fan, it will damage the fan’s   motor.  Only use a fan speed control to control a ceiling   fan.  Fan speed controls have special circuitry that will   not damage the motor.  For ceiling fans with a build in   light fixture, combination dimmer/fan speed control is   available. 

Q.   When I go to turn my dimmer off, it is very hot. Is this a   fire hazard?

A. Dimmers are rated for how many watts they are designed to   handle. If a dimmer has to operate at or close to its full   capacity, it will heat up. Some dimmers have metal fins on the front of them to enable proper heat dissipation. You can either reduce the wattage connected to the dimmer to   alleviate the problem, or put in a larger-rated dimmer.

Q. My lights dim or flicker when the microwave or other appliance   is used?

A. This   normally only happens in older homes. Older homes were not wired for the electrical usage of today’s homes and with all the modern day appliances most branch circuits in older homes are just overwhelmed, creating a draw that in turn momentarily dims the lights. Today’s homes have several more branch circuits to spread out the load on any given circuit and the main panels handle double the amperage. The other reason is generally associated with the neutral.A possible solution would be to upgrade your panel but is the cost worth the   occasional dimming of your lights? Probably not. 

Q. What causes a power loss?

A. Power loss may be caused by any unforeseen event that disconnects the power from your electrical system like energy shortage, a winter storm, or problem with a power line. 

Q. Why do circuits breaker trip?

A. When too many appliances are plugged in or turned on in the circuit, you will experience an overload which makes the circuit breaker trip. Other reasons are a faulty wiring or appliances that cause a short circuit. 

Q. What Causes A Power Loss?

A power loss  may be caused by a winter storm, an energy shortage, a summer brownout, a downed tree falling on a power line, an earthquake or any unforeseen event that cuts off the power to your electrical system.

Q. How can I prepare for Power loss?

A. You can install a backup power system, consisting of a generator connected to a switching panel. NICK Electric installs all sizes of emergency home generator systems according to your home needs.

Q. How does a generator work?

A. When the power goes out, a generator creates electrical power without using a utility's electrical source. Typically, a generator runs on fuel, like diesel, natural gas or LPG. When a generator is installed in your home, one main breaker is connected to your home's load center and the other main breaker is connected to your generator. The generator panel is then connected to circuits for critical electrical loads furnace, refrigerator, lights, sump pump, etc. - that you designate need to remain on during a power loss.

Q. What type of generator is right for my home?

A. The first step in purchasing a generator is to identify the things you absolutely cannot live without during a power outage. Usually high on the list will be the refrigerator and the freezer, a well pump, the furnace fan if you have natural gas or oil heat, and maybe some lighting.
NICK Electric can share more details with you, just give us a call to find out how you can protect yourself against power losses. 

Q.My house does not have grounded outlets.  Do I need to rewire my house?

A. No, in home wiring, prior the 1960’s, it was quite common to only have a 2 wire (not grounded) system.  The NEC allows the installation of GFCI outlets either at the first outlet  of the circuit or at every outlet.  They must however be labeled “ungrounded receptacle”. 

Q.My electric bill is too high.  is my electric meter spinning faster then it should?

A. No, all electric meters are calibrated once  by their manufacturer. Your meter is designed to spin by the electrical  energy that passes through it. Therefore, it is not possible that the  meter is “over spinning”. In some cases mechanical meters may spin  slower then they should due to gear issues.

Q. What can I do to prevent arc faults?

A. you can't prevent arc faults from occurring. However, there is a device that can stop them--by interrupting the electrical   current before any damage is done. It's called an Arc Fault   Circuit Interrupter (AFCI).  It electronically detects any   arc fault and stops the flow of electricity in a fraction of   a second. No electricity, no heat, no fire. And, by tripping   on a specific circuit, the AFCI helps you identify the   source of the problem right at the load center. 

Q. Do   fuses and circuit breakers serve the same purpose as AFCI's?

A. No. Fuses and circuit breakers cannot detect low-level arcs.   Only AFCIs are specifically designed for that purpose.

Q. Are AFCIs required by the National Electrical Code?

A. Yes. As of January 2010, arc fault circuit interrupters are  required by the National Electrical Code on all new bedroom circuits. But, you can protect you existing home too! By installing AFCIs now, you can get peace of mind from their added fire protection. 

Q. What surge protector is right for me?

A. Each type of surge protector focuses on a particular type of   wiring: electrical, telephone or coaxial cable. There are   two AC power surge protectors, allowing you protection   regardless of the brand of load center in your home. Ask   your NICK Electric’s electrician what type of protection is   right for you and your home.
 

Q. What are polarized electrical outlets?

A.   The different sized slots were developed to allow outlets to be polarized as a safety enhancement. The larger slot connects   the common wire in the outlet to the common wire in a device. The smaller slot connects the "hot" wires. By   forcing the smaller blade of the plug to always connect the   hot wires, the outlet is polarized. Devices, such as a table   lamp, are designed to minimize the risk of electric shock by   keeping the hot wire as short as possible by wiring directly   to the switch. The rest of the internal wiring connects to   the neutral wire. While this system does not eliminate the   possibility of electrocution, fire and electrical faults, it   reduces the risk by limiting the path of live current. 

Q. What   does the ground do? A. Another   improvement in safety came with the addition of a ground   wire to the outlet. This serves as an alternative return   path for electricity and is referred to as the equipment   ground. Ordinarily current flows from the hot wire and   returns via the common wire to ground. However, if the hot   wire comes in contact with a metal part of a device, the   outer cabinet housing of   a washing machine for instance, current could flow through   you to ground. The ground wire in a device connects to the   housing and provides a return path. The current could still   travel through you, but the ground wire probably has lower   resistance and so chooses that path over through you. Q. What is   a GFCI outlet?A.   GFCI   (ground fault circuit interrupter)  outlet is a device that adds a greater level of safety by reducing   the risk of electric shock. Most building codes now require   that a GFCI outlet be used in wet locations such as bathrooms, kitchens,   and laundry rooms. Q. I lost   power in my bathroom outlet, and all breakers are on.  What   can I do?

 A.   Typically   when a house is wired and has two bathrooms, the master bath   has a GFCI outlet that protects both bathrooms. The kitchen   has one that protects the other plugs close to the sink and   there is typically one in the garage that protects the   outlets there and perhaps the outside plugs as well. Often   times the GFCI outlet will go bad or is faulty, affecting   the other plugs downstream as it were.   

A.   Sometimes,   when you plug an electrical  appliance into an outlet, you may notice a small blue spark. In most   situations, this is a normal event as the electrons begin to   flow into the appliance's power cord. At other times,   however, a spark from an electrical outlet could start a fire or severely damage the plug. It is   important for homeowners to understand why an electrical outlet may spark or short   out without warning.

3640 Flagstone Circle Middleton, WI 53562